The Foundation of Plumbing Skills for Bathtub Installation
The Foundation of Plumbing Skills for Bathtub Installation
Blog Article
Have you been trying to find help and advice concerning Installing A Bathtub?
Installing a bath tub isn't precisely brain surgery, however it does require solid plumbing, woodworking, and also occasionally, tiling skills. Changing an old bath tub with a brand-new one is additionally a reasonably difficult project. If the old bathtub is conveniently accessible, the project can move quickly; if you have to open up a wall to eliminate the old bathtub as well as place the brand-new tub, the job is much harder. In either situation, the job is within a residence handyman's abilities, although you will require a helper to vacate the old tub and embeded in the brand-new one. Ensure you have qualified yourself for the task and also fit attempting it. As opposed to employing a professional to take control of a halfway-completed task, it is better to think about utilizing one before you begin. Chances are you might require a professional plumber to make tube links.
This post will certainly help you install a new tub in your bathroom if you have actually currently purchased a brand-new tub as well as do not require to change the plan of your previous supply of water pipes.
Your devices and also material checklist need to consist of the following:
Getting ready for the Installment
To start with, the sustaining frame provided with the bath needs to be fitted (if needed) according to the manufacturer's directions. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is important to see to it that if the tap comes with a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps unit to avoid stress on the bathtub.
Fit the versatile faucet adapters to the bottom of the two taps utilizing 2 nuts and also olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet with the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you utilize all of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should currently be ready to be suited its final setting.
Removing Old Touches
If you need to replace old taps with new ones as a part of your setup, then the first thing you must do is disconnect the water. After doing so, turn on the taps to drain any type of water remaining in the system. The process of eliminating the existing taps can be rather bothersome as a result of the restricted access that is often the instance.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the staying water that will originate from the pipelines. When the supply pipes have actually been removed, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary taps from turning throughout this process. Once the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned of any old securing compound.
Before proceeding to fit the brand-new faucets, contrast the pipe connections on the old faucets to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Mounting the Bathtub
Utilizing the two wood boards under its feet, position the tub in the needed placement. The wood boards are valuable in evenly spreading the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto 4 small factors.
The next goal is to make certain that the bath tub is leveled all round. This can be accomplished by inspecting the level and also adjusting the feet on the bathtub till the level checks out level.
To install faucets, fit the bottom of the outermost flexible tap adapter to the suitable supply pipeline by making a compression join; after that do the exact same for the various other faucet.
Turn on the water supply and inspect all joints and also brand-new pipework for leaks and tighten them if required. Load the bathtub as well as additionally check the overflow outlet and the regular outlet for leaks.
Ultimately, take care of the bathroom paneling as described in the maker's instruction manual. Tiling and also sealing around the bath tub ought to wait up until the bath tub has been used at the very least when as this will certainly settle it right into its last setting.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and the various other end supplies a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will certainly call for minimizing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the installing hole in the bath/basin making certain that the washing machines remain in area between the faucet and the sink. Safeguard the tap in position with the maker offered backnut. When the faucet is securely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with regular faucet adapters. The previous type should be linked to the tap ends initially, tightening just by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the area where the bath fulfills the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move sufficient to crack a rigid seal, triggering the water to permeate the wall surface in between the bath as well as the tiling, bring about complications with dampness as well as feasible leakages to the ceiling below.
You can select from a selection of coloured sealants to blend in your fixtures and fittings. They are offered in tubes and also cartridges, and also can securing spaces up to a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always fill the tub with water before securing, to permit the movement experienced when the tub remains in use. The sealer can break fairly early if you do not take into consideration this activity prior to securing.
Conversely, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently readily available on the marketplace. It is suggested to fit the ceramic tiles using waterproof or waterproof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I ran across that article about Installing A Bathtub when doing a search on the web. Do you know anybody else who is enthusiastic about How to Install a Bathtub? Do not hesitate to share it. We thank you for reading our article about Tools You Need to Install a New Bathtub .
Make An Appointment Report this page